Project: New Skylight Open Closed

Project Showcase

Project: New Skylight Open Closed

RH Renovation NYC completed a precision rooftop operable skylight installation and ventilation upgrade featuring structural rafter framing modifications, high-efficiency operable (open/closed) venting skylight unit mounting, rubberized ice-and-water flashing membrane encapsulation, custom interwoven step/counter-flashing tie-ins, and interior shaft finishing for a residential home in The Bronx, NYC. Rooftop penetrations across urban Bronx neighborhoods must withstand harsh microclimatic stresses—including heavy snow accumulation, winter freeze-thaw cycles, high wind-shear gusts, intense summer solar heat, and torrential downpours from seasonal nor’easters.

Integrating an operable (open/closed) venting skylight into a steep-slope roof assembly delivers both natural interior daylighting and passive thermal chimney ventilation, allowing trapped attic heat and humidity to exhaust naturally. However, creating a dynamic opening in a roof structure requires rigorous structural framing to preserve rafter load-bearing integrity and multi-layer flashing details to prevent leaks. Inferior skylight installations or compromised perimeter seals lead to immediate water infiltration, timber rafter rot, ceiling drywall collapse, and substantial thermal energy loss. This project was engineered to deliver an airtight, leak-proof, and fully operable daylighting and ventilation solution built to endure severe elevated urban weather.

Comprehensive Scope of Work & Installation Methodology

To satisfy strict New York City Department of Buildings (DOB) residential building safety codes and national roofing standards, our licensed and insured Bronx specialists executed a multi-phase technical installation protocol:

  • Structural Deck Cutout & Rafter Framing Modification: Technicians calculated structural roof load distribution before cutting the primary roof deck opening. Rafters were safely braced, severed, and framed out using double-header beams and trimmer rafters to restore full load-bearing capacity to the surrounding roof assembly.

  • Insulated Exterior Curb Construction: A rigid exterior mounting curb was built around the structural opening using dimensional lumber. The perimeter curb wall was fully insulated to eliminate thermal bridging and prevent interior condensation build-up along the light shaft.

  • Operable Venting Skylight Mounting & Low-E Glass Integration: A high-performance, factory-sealed operable venting skylight unit featuring dual-pane argon-gas-filled Low-E tempered safety glass was mounted onto the insulated curb. The smooth open/close mechanism was calibrated to ensure a weather-tight perimeter compression seal when closed.

  • Multi-Tier Flashing Membrane Encapsulation: Heavy-duty rubberized self-adhering ice-and-water shield membranes were wrapped continuously around the curb walls, extending outward across the surrounding subdeck plywood to establish a secondary fluid barrier beneath primary shingle courses.

  • Interwoven Metal Step Flashing & Sill Water Diversion: Custom aluminum sill flashings, side step flashings, and head saddle flashings were interwoven course-by-course with adjacent architectural shingles. This engineered drainage geometry directs wind-driven rain and melting snow sheet-flow cleanly around the unit without backing up under shingle edges.

  • Interior Shaft Alignment & High-Pressure Leak Audit: Interior drywall was extended up the light shaft and prepped for smooth finishing. A high-pressure water spray test was conducted across all frame seams and flashing points to verify absolute seal integrity and flawless operable mechanism function before site clearance.

Project Highlights & Technical Specifications

  • Service Category: Residential Rooftop Operable Skylight Installation, Structural Deck Reframing & Multi-Tier Flashing Weatherproofing

  • Project Location: The Bronx, New York, NY

  • Core Materials Used: Dual-pane argon-gas Low-E tempered safety glass operable skylight unit, structural framing lumber, self-adhering rubberized ice-and-water shield membrane, custom heavy-gauge aluminum step/sill/head flashings, CDX sheathing, and UV-resistant exterior polyurethane sealants.

  • Key Engineering Focus: Rafter load redistribution, operable weather-tight compression sealing, passive thermal exhaust ventilation, wind-shear resistance, and NYC DOB code compliance.

Results & Homeowner Value

By combining structural rafter reframing with multi-tier membrane weatherproofing and custom interwoven metal flashings, RH Renovation NYC permanently secured the new rooftop penetration. The Bronx homeowners now enjoy abundant natural daylighting, energy-saving thermal ventilation, and a completely leak-proof operable skylight system engineered to withstand severe seasonal weather for decades.

TALK TO THE TEAM

Our team is characterized by a group of professionals with a passion and love for our work

Portfolio

Recent Projects

View All
NYC Exterior Specialists

Ready to start your NYC renovation?

Professional renovation consultation in NYC.